[superhero06]

What do you do for a living???

[fobiawrx]

Originally Posted by superhero06

What do you do for a living???

Work for myself doing tile and finish carpentry

[stealthsti06]

very nice..serious stuff man

[superhero06]

You have some skills man. Nice work cant wait to see this monster finished.

[CenCali07STI]

If you do not mind me asking where did you get the flex sections at for your header? I am a sheetmetal worker by trade (actually and apprentice so still in the school) but during our school years we have year end projects. This year I am doing a pneumatic dirtbike lift and next year I plan on building a header for my 07. I know where to get all the tubing but not sure were to get the flex sections at.

[fobiawrx]

flex sections: http://www.prostreetonline.com/catalog/fabrication.html

tubing: http://www.globaltecheng.com/Product...?idCategory=65

[blaze0303]

i was reading this fourm hoping the car would be done by time i got to this page...but its not... HURRY UP AND FINISH I WANNA SEE THE FINAL PRODUCT! seriously though man, I wish I had ur skills and balls to do custom fab on my own sti...CHEERS!

[fobiawrx]

the next 2 weeks will be ordering everything i need to put it together and get it running. should be up by may....

[RallyBagger]

sweet man good to hear. It's gonna be a beast when it's done. Good luck with the rest of the build up!!!

[fobiawrx]

UPDATE! Project is at a stand still for now because my land lord thinks that welding is not a good thing to be doing at his house so I have to find a spot to finish up some stuff. Should be able to go to grimmspeeds new show witch happens to be a couple of blocks form me to weld so that might work out nice. Parts keep rolling in and stacking up. Still waiting on all the electronic stuff like the hydra, hydramist, e-boost controller, deffis, and some clips for the wiring harness. This is what my office is looking like these days:



Hears the 1600cc injectors:


Hears the heat mat for the bumper and alum box as well as the exhaust wrap and spay:


Clutch masters stage 5 clutch and act prolight fly wheel:


Pulleys, radiator hoses, and the end of a sparco harrness bar:


Now out in the garage it’s looking nice and clean because it was a hot 85 degrees last weekend so I was able to pull the whip out and wash it and clean up the place. hears the new ebay front lip that I got for $185 shipped that fits and looks vary good for the $$. A can of spray paint on it and looks as good as gold.



Parts all ready to be sent out to be coated:


All the parts that I need to do a little welding on:


and last all the little bits like the waste gates, cutouts, nuts and bolts, gaskets, ect are all stashed hear or in the rafters for now:


And for all you that have been wondering hear is a peek at the whole list:
1. 2.65 closed deck and sleeved block
2. Cp pistons
3. Oliver rods
4. balanced 2.5 lt crank
5. *******heads *******
6. *******valves and springs *
7. *******cams *****
8. comedic head gaskets
9. oversized head studs
10. cosworth oil pump
11. custom fog light twin scroll gt4088r turbo kit
12. two tial 44mm wastages
13. tial 50mm bov
14. 3inch with cut out dump exhaust (no cats) all heat coated and wrapped
15. 1600cc injectors
16. aps fuel rails
17. areomotive fuel pressure regulator
18. twin walbro pumps to a -10 line from pumps to motor. Hard lines back
19. hydra w/ wideband, flat foot shifting, anti-lag, and launch control
20. hydra mist
21. turbosmart e-boost controller
22. koyo radiator
23. unorthodox ultra ss pulley set
24. cusco hard mounts
25. ngk one step colder pugs
26. pe timing belt
27. aps 725 fmic
28. custom ic pipes
29. cosworth oil pump
30. ported tgvs
31. custom intake manifold
32. edelbrock 75mm dbc throttle body
33. wrx throttle cable
34. 160 thermostat
35. clutch masters stage 5 clutch
36. act pro light fly wheel
37. oil filter relocation kit w/ oil cooler


might be more but this is close. Stuff with ***** in it have yet to be purchased so I am not telling yet what im doing